**DISCLAIMER**
THIS IS NOT A REPLACEMENT FOR SERVICE INFORMATION. THIS IS INTENDED FOR INTERNAL USE BY MASS EMPLOYEES.
Mitsubishi
In the past Mitsubishi's late model lineup has not offered a diverse range of models. This would make it likely that service and repair information is consistent across the entire brand however due to an alliance with Nissan, Mitsubishi is now offering rebranded Nissan models. Starting with the 2022 Outlander (Nissan Rogue) you will find service information and procedures similar to Nissan rather than the traditional Mitsubishi SI. For the purpose of this reference, we have separated the Nissan information and source directories. Anything prefaced with (Nissan) references these Nissan platform vehicles specifically.
| Service | Requirement Examples | Source | Programming/Configuration Required? | Calibration Prerequitites |
|---|---|---|---|---|
| Front Radar |
If the ACC-ECU is replaced or removed and installed, use the following procedure to perform the radar calibration. Calibration required if codes C1758, C1768, C1769, C1772, C1773, C1774, or C1775 are set (Nissan) If distance sensor is being replaced or has been disconnected, perform "ADDITIONAL SERVICE WHEN REPLACING DISTANCE SENSOR" (calibration) Always perform the radar alignment after removing and installing or replacing the distance sensor. Always perform the radar alignment if rear axle toe settings have been made. Calibration required if code C2581 is set. |
SI - Radar R&R, SI - Calibration procedure (Nissan) SI - Radar R&R, SI - Calibration procedure |
Reset required when replaced (Nissan) Configuration when replaced |
Wheel Alignment (Nissan) Wheel Alignment Some full fuel tank |
| Windshield Camera |
Whenever you replace the FCM/LDW/AHB-ECU, calibrate it's sensor With code DTC C1754 Radar calibration not completed (Nissan) Always adjust the camera aiming after removing and installing or replacing the front camera unit. Always adjust the camera aiming after removing and installing or replacing the windshield glass. Calibration required if code C2503 is set. |
Section 54A / FCM/LDW/AHB / FCM/LDW/AHB / Removal and Instalation Section 54A / FCM/LDW/AHB / On Vehicle Service / Calibration (Nissan) Driver Assistance System / Removal and Installation / Front Camera / Removal and Installation Driver Assistance System / Basic Inspection / Additional Service When Replacing Front Camera Unit / Work Procedure |
When replaced or if code C2299 or U1195 is set | Some Full Fuel Tank |
| Windshield Replacement |
Whenever you removal the windshield, calibrate its sensor (Nissan) Similar |
Section 42A / Window Glass/ Windshield / Removal and Installation (Nissan) Glass and Window System / Removal and Installation / Window Glass / Windshied Glass / Removal and Installation |
||
| Blind Spot Radar |
When any of the followings is carried out, observe the procedure below to check the BSW-ECU. BSW-ECU removal and installation Modifying the rear bumper assembly. Calibration required if codes B2325 or B2326 are set. (Nissan) If side radar is being replaced or has been disconnected, perform "ADDITIONAL SERVICE WHEN REPLACING SIDE RADAR" Always perform the side radar alignment after performing the following work. After removing and installing or replacing the side radar. After removing and installing, replacing or repainting the rear bumper. Calibration required if codes C1E01, C1E10, C1E81, or C1E90 are set. |
Section 54A / Blind Spot Warning / BSW-ECU / Removal and Installation Section 54A / Blind Spot Warning / BSW-ECU / BSW Inspection (Nissan) Driver Assistance System / Removal and Installation / Side Radar / Removal and Installation Driver Assistance System / Basic Inspection / Additional Service When Replacing Side Radar / Work Procedure |
With code U1195 | Some require configuration |
| Park Assist | No known park assist calibrations or services | |||
| Multi-Around View Monitor (360 View) |
When you remove/install or replace the camera, you should check the camera image on the multi around monitor "Bird's eye-view." If necessary, calibrate the camera Calibrate according to the procedure below after the following operation is performed: Replacement of the camera-ECU Removal and installation/replacement of a camera Any of the door or the liftgate, Door mirror assembly (LH), (RH) is aligned. The front bumper face is deformed or loosened due to a collision accident. Calibration required if code B2548 is set. (Nissan) Perform the calibration and perform the writing to the around view monitor control unit when removing and replacing each camera, removing the camera mounting parts (front grille, door mirror, etc.) and replacing the around view monitor control unit. Perform camera aiming every time the front camera unit is removed and installed. Calibration required if codes B2A1A, B2A1B, B2A1C, or B2A1C are set. |
Section 54A / Around View Monitor / On Vehicle Service / Calibrating the Around View Camera Section 54A / Around View Monitor / Camera Removal and Installation (Nissan) Audio Visual & Navigation System / Intelligent Around View Monitor / Calibrating Camera Image / Work Procedure (Nissan) Exterior / Removal and Installation / Front Bumper / Removal and Installation |
Write learned value when ECU is replaced Variant coding when U1197 or U1195 is set | Control Module may Require Configuration |
| Front Bumper R&I |
When you remove/install or replace the camera, you should check the camera image on the multi around monitor "Bird-eye view." If necessary, calibrate the monitor (Nissan) When you remove/install or replace the front bumper assembly and camera, you should check the camera image on the multi-around monitor "Bird-eye view." |
NOT IN BUMPER R&R Section 54A / Around View Monitor / On Vehicle Service / Calibrating the Around View Camera (Nissan) Exterior / Removal and Installation / Front Bumper / Removal and Installation |
||
| Rear Bumper R&I |
Do not apply any sticker, paint or putty to the radar electric wave penetration area (shaded portion). However, only for Mitsubishi motors genuine color, paint can be repaired.Avoid any shocks or scratches. (Nissan) Post-installation Operation - Side Radar Alignment |
Section 51 / Rear Bumper Assembly / Removal and Installation (Nissan) Exterior / Removal and Installation / Rear Bumper / Removal and Installation |
||
| Door/Mirror R&I | When you remove/install or replace the camera, you should check the camera image on the multi around monitor "Bird-eye view." | Mirror R&I Procedure | ||
| PreScan/Post Scan Requirements | Scan Using MUT III required during collision diagnostics |
Section 52B / Post Collision Diagnosis (Nissan) SRS Airbag / Basic Inspection / Collision Diagnosis / [Applicable Procedure] |
||
| Occupant/Passenger Presence Calibration | (Nissan) Some require R&R inspection after collision with subsequent zero point calibration | (Nissan) SRS Airbag / Basic Inspection / Collision Diagnosis / [Applicable Procedure] | ||
| SRS Wiring Repair |
Do not attempt to repair the wiring harness connectors of the SRS. If any of the connectors are diagnosed as faulty, replace the wiring harness. If the wires are diagnosed as faulty, replace or repair the wiring harness according to the following table. (See vehicle specific table in SI) (Nissan) some require replacement of wiring harness instead of repair (must use circuit testing guided procedure to determine) Never solder the harness when making repairs. Check that harness is not pinched and that there is no contact with other components. |
Section 52B / Service Precautions (Nissan) SRS Airbag Control System / Precautions / Service Specific DTC troublshooting repair procedures for circuit in question (Repair or Replace) |
||
| SRS Misc. |
After deployment of an air bag, replace the SRS-ECU with a new one. When the SRS-ECU is replaced, VIN writing and coding must be performed. (Nissan) Similar |
Section 52B / SRS Control Unit / Removal and Installation (Nissan) SRS Airbag / Basic Inspection / Collision Diagnosis / [Applicable Procedure] |
||
| Impact Sensors |
Replace the sensors with new ones after the air bag has deployed. (Nissan) Similar |
Section 52B / Impact sensor / Removal and Installation (Nissan) SRS Airbag / Basic Inspection / Collision Diagnosis / [Applicable Procedure] |
||
| Steering Column Inspection | If a collision accident occurs or severe impact is applied on the steering wheel, the collision energy absorbing mechanism may have operated. Once the mechanism has operated, it will be inoperative even it has suffered no apparent damage. Determine if the steering column shaft can be reused by the following procedure. |
Section 52B / Post Collision Diagnosis - Steering Wheel Steering Column and Shaft Assembly Section 37 / On-Vehicle Service / Steering Column Shaft Assembly Shock Absorbing Mechanism Check |